Westermo DDW-226 Manual do Utilizador

www.westermo.com©Westermo Teleindustri ABUser Guide6642-22402Industrial Ethernet SHDSL extenderDDW-226 WOLVERINE SERIESWeOS

106642-22402Type tests and environmental conditionsPhenomena Test Description Test levelsESD EN 61000-4-2 Enclosure contact ± 6 kVEnclosure air ± 8 k

116642-22402DescriptionDDW-226 is an Ethernet extender with integrated switch and support for legacy serial connections. It uses the Westermo WeOS ope

126642-22402Interface specificationsPowerRated voltage 20 to 48 VDCOperating voltage 16 to 60 VDCRated current 330 mA (495 mA) @ 20 VDC (with 500 mA U

136642-22402Connection to console portThe console port can be used to connect to the CLI (Command Line Interface).The following steps needs to be tak

146642-22402Ethernet TX Electrical specification IEEE std 802.3. 2005 EditionData rate 10 Mbit/s or 100 Mbit/s, manual or autoDuplex Full or half, man

156642-22402* Direction relative this unit.Position Direction* Description1 In/Out 2-wire Receive/Transmit SHDSL2 In/Out 2-wire Receive/Transmit SHDS

166642-22402* Direction relative this unit.* Direction relative this unit.Position Direction* Description1 Out VBUS2 In/Out D–3 In/Out D+4 Out GNDSh

176642-22402LED indicatorsLED Status DescriptionON OFF Unit has no power.GREEN All OK, no alarm condition.RED Alarm condition, or until unit has start

186642-22402RemovalPress down the support at the back of the unit using a screwdriver. See figure.MountingMounting, 35 mm DIN-rail The unit can be mou

196642-22402Getting StartedThis product runs Westermo Operating System (WeOS) which provides several management tools that can be used for configurat

26642-22402Legal informationThe contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, eithe

206642-22402Factory default on DDW-226It is possible to set the unit to factory default settings by using two standard Ethernet RJ-45 cables.1. Power

REV.E 6642-22402 2015-01 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group CompanyWestermo Teleindustri AB • SE-640 40 Stora Sundby,

36642-22402SafetyBefore installation:Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check

46642-22402GeneralThis unit is intended for use in Zone 2 hazardous location only.Marking II 3G Ex nA IIC T4 Gc SPECIAL CONDITIONATEX InformationI

56642-22402SPECIAL CONDITION FOR SAFE USEAmbient temperature:This unit is designed for use in extreme ambient temperature conditions according to the

66642-22402RatingsPower (20 – 48) VDC; 330 mAAmbient temperature –40ºC ≤ Ta ≤ +70ºCIngress protection (IP) IP40Maximum surface temperature 135ºC (tem

76642-22402PositionDirection*/ descriptionInput/Output values12341 IO / Relay output +Uin = 60 VDC max Uin = 80 mA max2 IO / Relay output –3 IO / Digi

86642-22402FCC Part 15.105 Notice:This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 1

96642-22402Declaration of Conformity Westermo Teleindustri AB Declaration of conformity Org.nr/ Postadress/Postal address Tel. Telefax Post