Westermo ODW-710-F2 Guia do Utilizador

©Westermo Teleindustri ABUser Guide6651-2211Industrial Converter PROFIBUS DP to Fibre Optic Link. Point to Point applicationswww.westermo.comODW-710-

106651-2211Functional description Internal Electronics COM COM +VA OVP +VB C NO NC STATUS POWER LED’s OV P OC P RxD/TxD - P R

116651-2211Interface specifications* External supply current capability for proper startup PowerRated voltage ODW-710-F2: 12 to 48 VDC and 24 VAC

126651-2211PROFIBUS DP (RS-485)Electrical specification EIA RS-485 / EN 50 170Data rate 9 600 bit/s, 19.2, 93.75, 187.5, 500 kbit/s, 1.5, 3, 6 and 12

136651-2211FX (Fibre)Bi-Di LC-40Bi-Di LC-20Fibre connector LC Simplex LC SimplexFibre type Singlemode 9/125 µmSinglemode 9/125 µmWavelength nm, conn

146651-2211Location of Interface ports, LED’s and DIP-switchesODW-710-F2Position Direction* Description Product marking1 In Common voltage COM2 In Vol

156651-2211LED IndicatorsLED Status DescriptionPWR PowerON Power is on.Flashing Unit configured as focal point (DIP-switch S2:3 is ON).OFF Power is o

166651-2211DIP-switch settingsBefore setting DIP-switches:Prevent damage to internal electronics from electrostatic discharges (ESD) by discharging y

176651-2211S1 DIP-switchS2 DIP-switchDescriptionON 1 2 3 4 5 6 7 8ON 1 2 3 4 5 6 7 81 faulty frame before data rate seen as unidentified*. S1:

186651-2211Prepare the PROFIBUS units… Configure PROFIBUS network, with master and slaves. Check that the application is running correctly with the e

196651-2211If an optical fibre segment fails, all communication with units beyond the faulty fibre segment will be lost. To determine witch fibre se

26651-2211Legal informationThe contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, eithe

206651-2211Prepare the PROFIBUS units… Configure PROFIBUS network, with master and slaves. Check that the application is running correctly with the

216651-2211Data from the PROFIBUS master is received at the ODW-710-F2 electrical port (as indi-cated by the DPR LED). The data rate is automatically

226651-2211Calculating system processing delayData exchange between a PROFIBUS DP master and slave via ODW-710-F2 fibre optic link will be delayed due

236651-2211Reconfiguration time under faulty conditionThe reconfiguration time is determined by the time it takes to detect a faulty fibre seg-ment pl

246651-2211About the interfacesPower The power terminal has two independent inputs, +VA and +VB, allowing redundant power input. The ODW-710-F2 power

256651-2211About the automatic data rate detectionODW-710-F2 automatically detects the data rate by monitoring incoming PROFIBUS data frames on both t

266651-2211CoolingThis unit uses convection cooling. To avoid obstructing the air-flow around the unit, use the following spacing rules. Minimum spaci

REV.E 6651-2211 2013-06 Westermo Teleindustri AB, Sweden – A Beijer Electronics Group CompanyFor complete contact information, please visit our w

36651-2211SafetyBefore installation:Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Chec

46651-2211Note. Fibre Optic HandlingFibre optic equipment requires careful handling as the fibre components are very sensitive to dust and dirt. If

56651-2211GeneralThis unit is intended for use in Zone 2 hazardous location only.Marking II 3 G Ex nA IIC T4 Gc SPECIAL CONDITIONWARNING – DO NOT

66651-22111234Position Descripton Input / Output values1 In & out / Relay contact (NO)Uin = 60 VDC maxIin = 500 mA max2 In & out / Relay conta

76651-2211SPECIAL CONDITION FOR SAFE USEAmbient temperature:This unit is designed for use in extreme ambient temperature conditions as follows: –40 ºC

86651-2211Declaration of Conformity Westermo Teleindustri AB Declaration of conformity Org.nr/ Postadress/Postal address Tel. Telefax Po

96651-2211Type tests and environmental conditionsElectromagnetic CompatibilityPhenomena Test Description LevelESD EN 61000-4-2 Enclosure contact ± 6